Belkin Omniview SMB KVM-over-IP Switch F1DP108G Manuel d'utilisateur Page 1

User ManualF1DP108GF1DP116GOmniView® SMB KVM-over-IP SwitchOmniView® SMB KVM-over-IP Switch

712345678910section Overview(F1DP116G model shown)BANK               AutoScan Button7-Segment LED for BANK Identif

8OverviewSpecificationsPart No.: F1DP108G, F1DP116GNo.ofUsersSupported: 1 digital or 1 localNo.ofServersSupported: 8 and 16 respectively for

912345678910section OverviewDimensions: (F1DP108G) 17.25 x 1.75 x 7.5 in. (438 x 45 x 190mm) (F1DP116G) 17.25 x 1.75 x 7.5 in. (438 x 45 x 1

10OverviewSMB Server Interface Module, USBPart No.: F1DP101A-AUEmulation: Keyboard and mouse signalsPower: Via attached serverKeyboard/Mouse Connec

1112345678910section Local InstallationPre-Configuration(Typical Switch configuration)WheretoplacetheSwitch:The enclosure of the Switch is designe

12Local InstallationCable-DistanceRequirements(forPS/2,USB,andSunServers)VGA signals transmit best up to 100 feet (30m). Beyond that length, th

1312345678910section Local InstallationStep1 MountingtheSwitchNote: Before you begin, locate the MAC address and device number on the back of the

14Local InstallationStep2 ConnectingtheConsoletotheSwitch2.1 Connect your monitor VGA cable to the VGA port on the back of the Switch in the

1512345678910section Local Installation2.3 Locate and connect a cable from your local area network to the RJ45 Ethernet port on the back of the Swit

16Local InstallationStep3 ConnectingServerstotheSwitch (PS/2Connection)3.1 Make sure your server is powered off. 3.2 Using the Belkin Omn

Table of Contents1. Introduction ... 1 Package Contents ...

1712345678910section Local Installation3.4 Connect the Switch to the Server Interface Module using the included Belkin CAT5e Patch Cable or other

18Local InstallationStep3 ConnectingServerstotheSwitch (USBConnection)3.1 Make sure your server is powered on.3.2 Using the Belkin OmniVi

1912345678910section Local Installation3.4 Connect the Switch to the Server Interface Module using the included Belkin CAT5e Patch Cable or other CA

2020Local InstallationStep3 ConnectingServerstotheSwitch (SunMiniDIN8Connection)3.1 Make sure your server is powered off.3.2 Using the Be

2112345678910section Local Installation3.4 Connect the Switch to the Server Interface Module using the included Belkin CAT5e Patch Cable or other C

22Local InstallationStep4 PoweringUptheSystems4.1 If you have not already done so, power on all servers connected to the Switch (servers can be

2312345678910section Local InstallationDaisy-ChainingMultipleKVMSwitches(Optional)Note: If you are only installing a single SMB KVM-over-IP Switch

24Local InstallationBANK-DIP-Switch-ConfigurationChart (SMBCAT5KVMSwitches)DIP SWITCH# (SMB CAT5) BANK ADDRESS1 2 3 4N/A N/A N/A N/A BANK 00 Prim

2512345678910section Local InstallationExampleofDaisy-ChainConfiguration;X`jp:_X`e:fejfc\=C8J? C8E J<I@8C>fCfZXcBANK 00 SMB KVM-over-IP Swi

2626Local InstallationGetting Started:1. Make sure that all servers and Switches are powered off and that each KVM Switch has been assigned a unique

Table of Contents5. Using the Switch from a Remote Console ... 43 Starting a Remote Session ...

2712345678910section 2727Local InstallationConnecting the servers:1. Connect all servers to the SMB KVM-over-IP Switch and secondary KVM Switches. R

28Remote Installation Step1 IdentifyingtheIPAddressOnce your Switch has been connected to your network and is powered up, a Dynamic Host Configur

2912345678910section Remote Installation Step2 LoggingintotheWebInterface1. Open your web browser. If you are using Windows Vista, you must ru

30Remote Installation page (see Fig. 2). Fig. 2 Network-Configuration Page

3112345678910section Remote Installation Step3 NetworkConfigurationWhen first connecting to the Switch’s HTTPS configuration page, two browser secu

32Remote Installation Enable DHCPWhen this box is checked (default setting), a DHCP server on your network is enabled to assign an IP address to the S

3312345678910section Remote Installation Step4 UserSettingsIn the User-Profile page, you can create and edit up to 25 different user accounts. To o

34Remote Installation View OnlyA “view only” user is only allowed to view the screen of the target server without keyboard and mouse control. Only lim

3512345678910section Remote Installation To edit a user:1. Select the user from the list.2. Click . You can now change all the available parameters

36Remote Installation Step5 SwitchConfigurationThe Switch-Configuration page allows you to specify the KVM Switches daisy-chained to the SMB KVM-o

112345678910section IntroductionCongratulations and thank you for purchasing the Belkin OmniView SMB KVM-over-IP Switch (the Switch). This Switch prov

3712345678910section Remote Installation Tospecifyandnameservers:1. Click next to the Daisy-Chain field and select the KVM-switch configuratio

38Remote Installation Step6 SerialSettingsIf you have a serial device connected to the Switch, such as a power distribution unit (PDU), you must co

3912345678910section Remote Installation Step7 SecuritySettingsThe Security-Settings page allows you to configure security features for the Switch.

40Remote Installation Idle TimeoutSelect the maximum time allowed for inactivity before the user is disconnected from the remote session. Choose “No T

4112345678910section Remote Installation MaintenanceFirmwareUpgradeYou can upgrade the Switch’s firmware to take advantage of new features or fixes a

42Remote Installation Restore Factory SettingsYou can restore the Switch to its original factory settings. This restores the original parameters, rese

4312345678910section Using the Switch from a Remote ConsoleStarting a Remote SessionTo start a remote session:1. At a client computer, open Internet

44Using the Switch from a Remote ConsoleFull-Screen ModeYou can work on the target server in full-screen mode, just as if you were connected to the se

4512345678910section Using the Switch from a Remote ConsoleUsingtheDrop-DownBarThe quick-access, drop-down bar provides an easy method for changing

46Using the Switch from a Remote ConsoleMouse Configuration and SettingsMouse-Pointer AlignmentWhen working remotely at the client computer, two mouse

2OverviewRemote-Management Features•DigitalorLocalUser The Switch allows one user to access and control multiple servers from a local console, or

4712345678910section Using the Switch from a Remote ConsoleManual SettingsYou must manually synchronize the mouse pointers if:•themousesettingont

48Using the Switch from a Remote Console4. Follow the instructions and set any relevant sliders to the same values as set in the target server’s mou

4912345678910section Using the Switch from a Remote ConsoleAdvanced-MouseEmulationIn the Advanced-Mouse settings, you can set the type of mouse you w

50Using the Switch from a Remote ConsoleKeyboard Configuration and SettingsYou can define and transmit a keyboard sequence directly to the target serv

5112345678910section Using the Switch from a Remote Console4. Select the desired sequence and click “OK”. The sequence will appear in the Special-Ke

52Using the Switch from a Remote ConsoleVideo Configuration and SettingsRefreshYou may need to refresh the video image when changing the display attri

5312345678910section Using the Switch from a Remote ConsoleFig. 18 Manual Video-Adjust BarAuto Video AdjustTo adjust the video automatically:1. Open I

54Using the Switch from a Remote ConsolePerformanceSettings(Bandwidth)You can adjust the bandwidth settings on the Switch to give you the desired co

5512345678910section Using the Switch from a Remote ConsoleSelecting a ServerThe quick-access toolbar allows you to easily select and switch to any se

56Using the Switch from a Remote ConsoleAdditional FeaturesWhen you click in the quick-access toolbar, a menu will appear. From this menu you can ac

312345678910section Overview•VideoResolution The Switch supports video resolutions of up to 1600x1200 @ 75Hz for both local and remote consoles.Oth

5712345678910section 57Using the Switch from a Remote ConsoleRestoringFactoryDefaultsThe “Restore Factory Settings” section below explains how to re

58Using the Switch from a Local ConsoleNow that you have connected your console and servers to the Switch, it is ready for use. You can select connec

5912345678910section Using the Switch from a Local ConsoleWith a daisy-chain switch configuration, you can switch between BANKs (KVM switches) by pres

60Using the Switch from a Remote ConsoleSelecting a Server Using Port SelectorsYou can directly select which server you wish to control by pressing th

6112345678910section Using the Switch from a Remote ConsoleAutoScan ModeThe AutoScan feature allows you to set your Switch to scan and monitor the act

62Using the Switch from a Remote ConsoleOn-ScreenDisplay(OSD)The OSD allows you to switch servers, assign names to your servers, enable and disable

6312345678910section Using the Switch from a Remote ConsoleOSD-Menu Keyboard CommandsCommand FunctionèêNavigate to different servers in the same BANKP

64Using the Switch from a Remote ConsoleFunction/Help-PageKeyboardCommandsCommand FunctionF4 Initiate AutoScanèêNavigate to the next fieldInsert Hig

6512345678910section Using the Switch from a Remote ConsoleHot KeyThis allows you to select which key will be used to initiate hot-key commands. You h

66Using the Switch from a Remote ConsoleHot-Key-Command ShortcutsBelow is a complete list of hot-key commands that can be used for your Switch:Command

44OverviewEquipmentRequirementsServer Interface ModulesConnecting the Switch to a server requires a custom Belkin OmniView SMB Server Interface Modul

6712345678910section 67Using the Switch from a Remote ConsoleSun Combo KeysThe PS/2 keyboard connected to the Switch does not support the Sun keypad t

68Using the Switch from a Remote ConsoleUpdatingFirmwareThe Switch features flash-upgradeable firmware to ensure compatibility with the latest device

696912345678910section Frequently Asked QuestionsWhatoperatingsystemsdoestheSwitchsupport? The Switch will support operating systems that run o

70Frequently Asked QuestionsDoestheSwitchsupportLinux? Yes, the Switch works with Red Hat and other Linux distributions configured for PS/2 or US

7112345678910section Troubleshooting Local ConsoleGeneralProblem:My server does not boot when connected to the Switch but works fine when I connect th

72Troubleshooting KeyboardProblem:The server does not detect a keyboard and I get a keyboard error reported at boot up.Solution:•Checkthatthekeyb

7312345678910section 73Troubleshooting Problem:When I switch from one port to another, mouse movement is completely erratic.Solution:•Makesureyo

74Troubleshooting Remote ConsoleProblem:The Remote console login page will not display on my browser.Solution:•VerifythatyouareusingMicrosoftI

7512345678910section Troubleshooting Problem:The video quality is bad and/or grainy.Solution:•Usethequick-accesstoolbartorefreshthevideoscree

76GlossaryThe following definitions are used throughout this User Manual.AutoScan: A mode of operation where the KVM switch scans from one port to ano

512345678910section OverviewCablesBelkin highly recommends you use Belkin Category 5e, FastCAT5e, or Category 6 Patch Cables for your SMB KVM-over-IP

7712345678910section Glossary KVM: Literally “Keyboard Video Mouse”, this term refers to technology that allows two or more computers to be controlle

78InformationFCC StatementDeclarationofConformitywithFCCRules forElectromagneticCompatibility We, Belkin International, Inc., of 501 West Wa

7912345678910section Informationpurchaser, or if Belkin determines that the Belkin product has been improperly installed, altered in any way, or tampe

8012345678910section InformationThis warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state.

P75215-ABelkin Tech SupportUS: 800-223-5546 ext. 2263 310-898-1100 ext. 2263UK: 0845 607 77 87Australia: 1800 235 546New Zealand: 0800 235 546

6OverviewSystem RequirementsOperating-System(OS)PlatformsThe SMB KVM-over-IP Switch is compatible with CPUs running on, but not limited to, the foll