Belkin F5U222V Fiche technique télécharger pdf

TMP3200/090 DATASHEET

System Overview

The Telesis

TMP3200/090 PINSTAMP

marking system

permanently prints messages into a variety of materials such as steel,

aluminum, and plastic. A hardened pin is pneumatically accelerated to

indent dot matrix characters into the item being marked. The shape,

size, density, and location of characters are determined by the user

through the system software. The marking head moves the pin

cartridge through X- and Y-axis motions to reach the correct position

for each dot of the characters to be marked. The system software

automatically controls pin extension and retraction to mark the

message.

TMP3200 Marking Head includes the mechanical motion

components to position the marking pin at precise X/Y positions

and the pneumatic components to drive the marking pin out from,

and return the pin into, the pin cartridge.

The TMP3200 marking head is an X/Y-traversing mechanism.

Using two stepper motor drives, it accurately and rapidly positions

the pin at coordinate-defined locations in marking window within

.03175 mm (.00125"). The marker accommodates the rigorous

dynamics of impacting, rebounding, and rapid positioning of the

marking pin through a system of rigid rails and ball bearing

saddles, timing belts, and direct-drive, toothed pulleys.

The floating pin design permits high quality, consistent marks on

irregular, slightly curved surfaces. It also accommodates applications

where marking surfaces cannot be positioned at a consistent distance

from the marker.

The internal mechanism is protected from debris by an integral

shield. Stainless steel panels slide against one another, constrained

by the cartridge and the high-impact ABS cover, to prevent debris

from entering the marking head.

Marker Cable, pre-wired to the marking head, connects the

marker to the controller. The highly flexible cable is 4m (13 ft.

long. Optional extension cables are available for greater distances.

TMP3200/090 Marking System – General Arrangement

Marking Pins for the TMP3200 include the 25S-, 25L-, 25XL- and

the 150SA-series. Refer to the marking head installation drawing

for pin stroke (pin extension) dimensions. Refer to the marking

depth tables for pin cone angles and depths.

Filter/Regulator Unit includes two regulators with pressure

gauges to control the drive air and return air. The first regulator

contains a filter to help remove contaminants from the supply air.

Two air lines connect the regulated air to the marking head. Drive air

fires the impact pin; return air pushes it back into the cartridge. The

standard air lines are 4m (13 ft.) long made of 6 mm tubing.

System Computer runs the Merlin

II marking system software

and generates commands to control the marker. The system

computer must

be equipped with an add-on USB v2.0 board and

must

satisfy one of the following configurations:

• Windows

2000 or Windows

XP or Windows

Vista™ operating

system with Belkin

model F5U219 PCI USB 2.0 board

(full-size PCs);

• Windows

2000 or Windows

XP or Windows

Vista™ operating

system with Belkin

model F5U219LP PCI USB 2.0 board

(low-profile PCs);

• Windows

2000 or Windows

XP or Windows

Vista™ operating

system with Belkin

model F5U222 or IOGEAR

model GPU202

PCMCIA USB 2.0 board (laptop or notebook PCs).

To take full advantage of the Merlin

II RS232 or TCP/IP

capabilities, the system computer must have an available RS232 or

TCP/IP port for the host interface.

TMC090 Controller connects to the system computer through a

USB interface. Commands are passed from the PC to the controller,

then on to the marker and its optional equipment. The TMC090

interface panel provides ports for connecting additional I/O devices

for remote operation.

1 2 3 4 5 6

Résumé du contenu

Page 1 - TMP3200/090 DATASHEET

Page 2 - TMP3200/090 DATASHEET

TMP3200/090 DATASHEET Doc. No. 37061 Rev. J 2 of 6 System Setup When designing a fixture, allow for 3-axis adjustment to aid in horizontal, verti

Page 3

TMP3200/090 DATASHEET Doc. No. 37061 Rev. J 3 of 6 TMP3200 Marking Head Specifications. The TMP3200 marking head specifications are subject to ch

Page 4

TMP3200/090 DATASHEET Doc. No. 37061 Rev. J 4 of 6 TMC090 Controller Specifications. The TMC090 controller specifications are subject to change

Page 5

TMP3200/090 DATASHEET Doc. No. 37061 Rev. J 5 of 6 Interface Panel. The interface panel provides various ports for connecting the controller to t

Page 6

TMP3200/090 DATASHEET Doc. No. 37061 Rev. J 6 of 6 Extended Protocol. This protocol selection includes error checking and transmission acknowledg

Commentaires sur ces manuels

Pas de commentaire

Belkin F5U222V Fiche technique

Naviguer en ligne ou télécharger Fiche technique pour Non Belkin F5U222V. Belkin F5U222V Datasheet Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Belkin F5U222V